HDMI Scaler/Switch
Quick Start Guide
English
LINDY No. 32596
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (September 2007)
HDMI Scaler/Switch
User Manual
1. Introduction
Thank you for purchasing the LINDY HDMI scaler with remote control. This high
performance scaler is designed to upscale digital & analogue signals from Composite,
S-Video, PC, Component (HD) and HDMI devices to a digital HDMI output. Besides
up scaling to HDTV (1080p) and WUXGA (1920x1200) the scaler also converts
analogue audio to digital then outputs through HDMI or coaxial S/PDIF.
The scaler also has a comprehensive on screen display menu to allow you to select a
variety of output resolutions for best picture quality.
2. Features
•
HDMI1.2, HDCP 1.1 and DVI 1.0 Compliant
Automatically detects the resolution of the connected display
Supports 50/60Hz frame rate conversion
•
•
•
Supports 3D motion video, 3D de-interlacing and 3:2 / 2:2 pull down detection
and recovery
•
Provides output picture adjustment on contrast, brightness, hue, saturation,
sharpness, RGB (colour tone) level and aspect ratio size
Ideal for home theatre integration, conference room and retail stores
Supports high resolution input/output
•
•
• PC: VGA, SVGA, XGA, SXGA, UXGA & WUXGA
• HDTV: 480i, 576i, 576p, 1080i & 1080p
RS-232 port for firmware upgrade
•
•
•
Digital and analogue audio input and digital output
IR remote control
3. Operation Control
Front Panel
1. Power switch and LED indicator (LED will illuminate when power is turned on)
2. Remote control sensor
3. Input select/Indicators:
Press the desired button (CV, SV, Comp, PC, HDMI) to select the input
source and the LED will illuminate to indicate which input source is selected
and routed to the display
4. Press the menu button to bring up the OSD operation menu
5. When in the OSD use these buttons to move up and down
6. Use the enter button to confirm the selection when using the OSD
HDMI Scaler/Switch
User Manual
Rear Panel
1. HDMI & CO-AX Out:
Connect the HDMI output port to the HDMI input port of your display. Connect
the Coaxial output port to an external amplifier
2. Aux Input Port:
When using the HDMI input port with DVI, connect the audio from the DVI device
to the Aux input port
3. HDMI Input:
Connect your HDMI sources such as DVD player or set top box to these inputs
4. RS-232 Port:
This port is for firmware update only
5. PC in:
Connect your VGA cable from your PC to the PC in port and connect the stereo
jack from your PC to the PC in audio port
6. Y Cb/Pb Cr/Pr Video and L/R Audio Input:
Connect the Y Cb/Pb Cr/Pr (Component) RCA input ports to the Component
output port of your video source equipment such as DVD player or Set-Top-Box.
Connect the L/R audio input ports to the audio output port of your audio source
equipment
7. CO-AX Input:
The CO-AX port is for digital audio input and can be used to combine with each
video input signals from CV/SV/COMP/PC/ HDMI ports. Once connected, please
use the Audio Source Selection in the OSD menu to select between Coaxial
(S/PDIF) or other audio source
8. CV / SV and L/R Audio Input:
Connect the Composite or S-Video input port to the Composite or
S-Video output port of your video source equipment such as DVD player or
Set-Top-Box. Connect the L/R audio input ports to the audio output port of
your audio source equipment
9. Power:
Plug the 5VDC power supply into the unit and connect the adaptor to
AC wall outlet
HDMI Scaler/Switch
User Manual
4. OSD Operation
HDMI Scaler/Switch
5. Remote Control
1. POWER:
User Manual
Press the button once to power on the unit.
Press again to enter standby mode.
2. INPUT:
Press the button repeatedly to toggle
through the various input sources.
3. HD Input:
Press the button to directly select
component input.
4. PC Input:
Press the button to directly select PC input.
5. HDMI/DVI Input:
Press the button to directly select HDMI (or
DVI) input.
6. Output Resolution:
Press any one of the buttons to directly select
output resolution. For other output resolutions
that are not covered by these buttons please
enter OSD Menu to select them.
7. MENU:
Press the button to bring up the OSD main
menu page.
8. Exit:
Press the button to exit from a sub menu or
main menu.
9. Up/Down/Left/Right:
Press the Up/Down button to move the
highlight bar to your desired parameter
during the OSD operation. Press the
Left/Right button to increase/decrease the
setting value of a selected parameter.
10. OK (Enter):
Press the button to confirm your selection.
11. Reset:
Press the button to reset the unit's firmware
setting to the factory default value.
12. Auto Adjust:
Press the button to optimize the position of
the picture (picture centering) on the
screen.
6. Specifications
•
Frequency bandwidth: 1.65Gbps (Single Link)
Input Ports:
Composite & L/R audio
•
S-Video & L/R audio
Component (3 RCA) & L/R audio
PC D-Sub (15-pin) & 3.5mm Jack
HDMI & 3.5mm Jack (for DVI)
HDMI Scaler/Switch
User Manual
Coaxial (S/PDIF)
•
Output Ports:
HDMI
Coaxial
•
•
•
5V DC power supply
Dimensions: 215 x 154 x 47 (WxDxH)
Weight: 1Kgs
7. Connection & Installation
CE/FCC/WEEE/Statement
CE Statement
This device complies with the European Regulations for Electromagnetic Compatibility (EMC) of the European Union and
it is equipped with the CE mark. This unit has to be used with high quality shielded connection cables. Only if these high
quality shielded cables are used it can be sure that the EMC compatibility is not adversely influenced.
FCC Statement
Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission
regulations and ensure a suitably high level of immunity to electromagnetic disturbances.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B Digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
ꢀ
ꢀ
ꢀ
ꢀ
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced technician for help
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and
electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these
products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways.
Please follow your national law when you want to dispose of any electrical or electronic products.
More details can be obtained from your national WEEE recycling agency.
Germany / Deutschland
Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das Recycling
von Elektro- und Elektronikprodukten geschaffen. Diese wurden von der Bundesregierung im Elektro- und
Elektronikgerätegesetz – ElektroG in deutsches Recht umgesetzt.
Dieses Gesetz verbietet vom 24.März 2006 an das Entsorgen von entsprechenden, auch alten, Elektro- und
Elektronikgeräten über die Hausmülltonne! Diese Geräte müssen den lokalen Sammelsystemen bzw. örtlichen
Sammelstellen zugeführt werden! Dort werden sie kostenlos entgegen genommen. Die Kosten für den weiteren
Recyclingprozess übernimmt die Gesamtheit der Gerätehersteller.
France
En 2006, l'union Européenne a introduit la nouvelle réglementation (DEEE) pour le recyclage de tout équipement
électrique et électronique.
Chaque Etat membre de l’ Union Européenne a mis en application la nouvelle réglementation DEEE de manières
légèrement différentes. Veuillez suivre le décret d’application correspondant à l’élimination des déchets électriques ou
électroniques de votre pays.
Italy
Nel 2006 l’unione europea ha introdotto regolamentazioni (WEEE) per la raccolta e il riciclo di apparecchi elettrici ed
elettronici. Non è più consentito semplicemente gettare queste apparecchiature, devono essere riciclate.
Ogni stato membro dell’ EU ha tramutato le direttive WEEE in leggi statali in varie misure. Fare riferimento alle leggi del
proprio Stato quando si dispone di un apparecchio elettrico o elettronico.
Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato.
LINDY No. 32596
|