Kuppersbusch USA Cooktop EGS 3042 User Manual

Installation instructions  
Important - Save for the local electrical inspector’s use.  
EEB 6800.0  
EEB 6600.0  
EEB 6500.0  
1
B
43I  
24  
07  
 
General  
Installation requirements  
The oven must be placed on a board that can support a minimum of 62.5 kg/  
140 lb. The oven is placed in direct contact with the side walls of the opening  
with the frame overlapping these side walls.  
Turn off the power source before installing the oven.  
=
WARNING! In case the oven is not installed and secured in accordance  
with this installation instructions, there is a risk of tipover! Check after  
installation that the fastening screws are securely seated and that the ap-  
pliance cannot be moved.  
=
WARNING! The furniture or adjacent side walls must be secured so the installed  
oven can’t tilt.  
Make sure there’s an opening in the back so there is enough air available for  
cooling the oven. If there isn't an opening, cut a hole with at least 300 cm2/  
45 in2 depth in one of the adjacent surfaces, preferably in the bottom board  
or top cover.  
Only KÜPPERSBUSCH built-in cooktops have been designed and tested  
for installation above a KÜPPERBUSCH built-in oven. No other cooktops  
may be used above the oven.  
=
=
Only qualified personnel should perform installations and repairs on elec-  
trical appliances. Do not repair or replace any part of the appliance unless  
specifically recommended in this manual. Do not put your safety at risk.  
All components surrounding the oven should have a temperature resistance of up  
to 100 °C/210 °F. This includes varnishes, edge bands, plastic surfaces, adhe-  
sives and paints. The adjacent furniture fronts should be temperature-resistant up  
to at least 70 °C/160 °F.  
To eliminate the risk of burns or fire by reaching over heated surface units,  
cabinet storage space located above the surface units should be avoided. If  
cabinet storage is to be provided, the risk can be reduced by installing a range  
hood that projects horizontally a minimum of 5 inches beyond the bottom of  
the cabinets.  
Installation in a high cabinet  
The frame of the oven overlaps the side walls on the right and left.  
Installation under a countertop  
The frame of the oven overlaps the boundary of the opening on all sides.  
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0  
3
 
Installation under a cooktop  
Electrical supply  
The following KÜPPERSBUSCH built-in cooktops may be installed above the  
oven:  
Only a qualified technian can install a conduit box or replace a connection  
cable.  
=
Conduit box  
Don’t install the conduit box in the installation area or above a worktop!  
Attach it to the side, underneath the wall, or in a high cabinet under the in-  
stallation surface.  
There must be a hole for the conduit cable in either the bottom opening or  
the wall.  
Electrical supply  
The power supply should be a 120/240 volts system, 3-wire with ground.  
Electrical diagram  
for a 120 / 240 volts system,  
3-wire with ground:  
Model:  
„A“  
„B“  
„C“  
EKE 854.1  
EKE 854.2  
EKE 804.2  
EKE 604.2  
103 mm  
4-1/16"  80 mm  3-1/8"  
3-13/16"  80 mm  3-1/8"  
Be sure to install an appropriate conduit box (not furnished) to connect the oven.  
Don’t shorten the conduit to facilitate service! The conduit should be routed  
to permit the removal of the oven.  
EGS 304.0*  
EKS 304.1*  
97 mm  
85 mm  
3-3/8"  
 65 mm  2-9/16"  
Installation, electrical connections and grounding must comply with all appli-  
cable local codes.  
EKS 604.2  
EKS 804.2  
103 mm  
4-1/16"  80 mm  3-1/8"  
The conduit-box must be protected by a circuit breaker or fuse, having  
amperage as noted in this chapter.  
* The gap between the countertop and the front panel is not necessary  
for the models EGS 304.2 and EKS 304.1.  
Connected load  
Fuse current  
240 V, 60 Hz, 3.6 kW  
15 A  
F
F
You will find the recess size and installation conditions for the cooktop in  
the installation instructions for the cooktop.  
 Connect the cable to the conduit box.  
When the oven is connected, the clock flashes! Set the time as described  
in the user’s guide.  
F
Installation  
Inserting the appliance  
 Push the appliance right into  
the cabinet opening. Don’t  
pinch the appliance cable!  
Fastening the appliance  
 Open the oven door and attach the  
appliance with the enclosed screws -  
inserted at an angle - to the cabinet  
element from the inside out.  
4
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0  
 
Installing the individual telescopic  
glide-out shelves (acc.-no. 601)  
 Unscrew the side grids.  
These screws are used to fasten the individual telescopic glide-out shelves.  
 Insert the individual telescopic  
glide-out shelves at the back  
into the holes in the  
intermediate wall and screw  
the individual telescopic glide-  
out shelves at the bottom front  
to the side walls. (With the  
shelf rack screws!)  
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0  
5
 
6
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0  
 
KÜPPERSBUSCH  
112 N. East Street, Suite C  
Tampa, Florida 33602  
Telephone: 813-229-7096 Fax: 813-229-0982  
Customer Care line: 1 - 800 - 459 - 0844  
KÜPPERSBUSCH is a brand of Teka USA, Inc.  
 

Lasko Electric Heater 5842 User Manual
Lenoxx Electronics Air Conditioner HS32 Series User Manual
Lightolier Indoor Furnishings 1001FR Series User Manual
Lincoln Electric Soldering Gun K1809 1 User Manual
Linksys Switch SVIEW08 v2 User Manual
LOREX Technology Home Security System SG15F6584 User Manual
Maxon Telecom Two Way Radio GMRS 21X User Manual
Maytag Dishwasher MDB4621AWB0 User Manual
Maytag Microwave Oven W10191953A User Manual
M S Cash Drawer Printer 7193 User Manual